Good foundation is important first step of tiling

Q: I’m going to replace my countertop with ceramic tile and so I have removed my old laminate one leaving nothing but the cabinets below. I have done some small floor tiling projects but never a countertop. I’m going to reuse my drop-in sink and faucet, but how do I go about building the base that the tiles will sit on?

A: Tiling a countertop is like building a house: If the foundation is weak, you are going to have problems. Once the foundation is down, the tiling part of the job goes pretty quickly.

You are going to lay down a ¾-inch sheet of plywood and, depending on the height of the edge tiles, lay down a sheet of ½-inch cement board on top of it. This whole mess will be mortared and screwed together.

Start by installing ledger boards on the perimeter walls if there is no support there, and screw the ledger boards to the wall studs.

Cut sheets of ¾-inch plywood to sit on top of the cabinets so that the edge of the plywood sits evenly with the frame of the cabinets. Drill pilot holes in the top of the cabinet frame and screw the plywood to the frame and along the ledger boards.

Now, check out the height of the edge tiles. These are called “V” caps and have a rounded edge that transitions the horizontal surface to a vertical one. If the height is such that they may interfere with the operation of the doors, then you will need to add an additional layer of plywood. If this is necessary, use construction adhesive and screws.

Flip your sink upside down on the plywood and make a mark around it. Remove the sink and make another mark inside the first line so that the sink rim will have enough area on which to rest. Drill a hole inside this second line and cut out the area with a jigsaw.

As a final step for the base, lay a sheet of ½-inch cement board on top of the plywood. Trowel a layer of thin-set mortar on the plywood and screw it down. You can cut the cement board by scoring one side and snapping it or by using an abrasive blade in a jigsaw.

You will also want to reinforce the edges, so add a strip of cement board equal to the thickness of the base. Use galvanized nails to secure it and then wrap the edges with fiberglass tape before embedding it in a thin layer of thin-set mortar.

Now you’re ready to lay out the tile.

There are no hard and fast rules for tile layout except that you want to avoid thin pieces of tile. Pick a spot that is highly visible and start by laying out tiles across the surface. If your counter changes direction rather than just a straight run against the wall, a corner area is a good place to start.

Some tiles have built-in lugs to keep them evenly spaced and some will require you to install spacers (or you can just eyeball the spacing). Lay out the tiles and use a framing square to make sure the lines are straight. You can snap chalk lines and lay one row in each direction.

If you end up with a thin piece of tile on one side, move the tiles over to eliminate the slivers. Then you can snap a new chalk line.

Mix up a batch of thin-set mortar and trowel it on with a square-notched trowel. Lay the tiles in sections. When you have completed one section, move to the next.

When it comes time to cut a tile, you can rent a wet saw or you can buy a cheap one for less than $100, and it will work great for this job.

When it comes time to install the V-cap tiles, you can clamp a board to the cabinets as a place for the tile to sit against until the mortar cures, or you can tape the V-caps to the tiles in front of them.

For the backsplash, either line up the grout lines or make the backsplash tiles line up halfway between the field tiles. Let the mortar cure according to the manufacturer’s specifications (usually 24 hours).

To grout, you’ll need a grout float (a piece of rubber attached to a handle), bucket of water, large sponge and dry white rag. Mix the grout, then use the grout float to push it into the spaces between the tiles. Keep the face of the float at an angle and pull it diagonally across the face of the tiles filling every nook and cranny.

Wring out the sponge in clean water and wipe up the excess grout. When the sponge gets clogged with grout, dunk it in the water and wring it out.

About 15 minutes after you sponge off the grout, you’ll notice a haze forming on the tile. Use the rag to buff it off. You should do this promptly. After that just reinstall the sink.

Mike Klimek is a licensed contractor and owner of Las Vegas Handyman. Questions may be sent by email to handymanoflasvegas@msn.com. Or, mail to 4710 W. Dewey Drive, No. 100, Las Vegas, NV 89118. His web address is www.handymanoflasvegas.com.

Life Videos
MAGIC fashion convention showcases men's clothing trends
The MAGIC fashion convention has come to Las Vegas at the Mandalay Bay Convention Center to showcase some of the hottest clothing trends for men. (Nathan Asselin/Las Vegas Review-Journal)
Former Army medic’s Afghanistan story told in new book
The graphic novel “Machete Squad” is based on journals written by Las Vegan Brent Dulak.
Las Vegas man talks about losing his wife
Dwayne Murray, 37, lost his wife, LaQuinta while she was at Centennial Hills Hospital. A jury awarded him $43 million last week after it said the hospital failed to perform the standard of care in administering a drug for her sickle cell disease.
Barber sets up shop in grandfather’s old shop
Andres Dominguez’s new barber shop is filled with memories of his grandfather, who ran the El Cortez landmark for more than 30 years. (John Przybys/Las Vegas Review-Journal)
Life and times of a 90-year-old horse player
Leo Polito of Las Vegas describes meeting legendary jockey and trainer Johnny Longden on the beach at Del Mar. Mike Brunker/Las Vegas Review-Journal.
Learning the history of singing bowls
Presentation at Summerlin Library teaches residents about the history of singing bowls (Mia Sims/Las Vegas Review-Journal)
Learning live-saving techniques in Stop the Bleed class
Leslie Shaffer, an AMR paramedic, shows how to control bleeding during a Stop the Bleed course at the Summerlin Library. The class is designed to teach anyone how to control and stop life-threatening bleeding. (Mia Sims/Las Vegas Review-Journal)
Vicki Richardson speaks about on the power of art
Artist and arts advocate Vicki Richardson talks about the power of art to inspire and challenge. (John Przybys/Las Vegas Review-Journal)
DressCoders pairs tech with haute couture
DressCoders is a startup focused on haute couture garments. The company uses illuminated thread that is washable and can be sewn right into the fabric. (Mat Luschek/Las Vegas Review-Journal)
CES 2019: Brava infrared oven
In cooking with the Brava infrared oven,there’s no preheating. the bulbs can reach 500 degrees in less than a second. (Heidi Knapp Rinella/Las Vegas Review-Journal)
Sinks Merge Style And Utility
Study could determine cause of Alzheimer’s, Parkinson’s diseases
Dr. Aaron Ritter, director of clinical trials at the Cleveland Clinic Lou Ruvo Center for Brain Health, discusses his research on how inflammation in the brain impacts Alzheimer’s and Parkinson’s diseases. (Jessie Bekker/Las Vegas Review-Journal)
Holocaust survivors talk about tragedy and friendship
Janos Strauss and Alexander Kuechel share their perspectives on life. (John Przybys/Las Vegas Review-Journal)
'Siegel Cares' Santa delivers toys to kids at Siegel Suites in Las Vegas
Siegel Cares, the charitable wing of The Siegel Group, delivered toys to families at their apartment complexes in Las Vegas. (K.M. Cannon/Las Vegas Review-Journal)
Revisiting “Christ the King” sculpture
A longtime admirer of the sculpture at Christ the King Catholic Community in Las Vegas shares her perspective. (Bizuayehu Tesfaye/Las Vegas Review-Journal @bizutesfaye)
TOP NEWS
Home Front Page Footer Listing